I’ve had this table saw about a year and have had very good results making precision cuts with the rip fence. Ease of use has been great. Get it out set up and get to making cuts fast. I am not making a daily living with it so I may not notice some short comings that daily users would. Maybe like with hand tools, someone won’t notice the difference between Snap-on or Craftsman wrenches until you make a living with them.
I only have two minor concerns with this saw but they are so small that this saw still gets a 5 star rating.  DEWALT could step up the game on the dust collection if they offer users an effective way of using the dust port on the blade guard. Maybe they offer an accessory splitter and hose package. My other concern is the plastic parts on the fence where it connects to the table. I suspect those parts could break when they are cold if you remove the fence and toss it in the trailer or back of your truck. Again, these are minor in comparison to the rest of the saw (food for thought on the next design).

dewalt dwe7491rs without stand Amzon.com


I tested both saws and found their performance similar, though thanks to the rolling stand, I was more likely to reach for the DeWalt. If you don’t value the stand, the SKILSAW packs a lot of power in a small form and is the preferred job site saw of several local contractors I know. If you’re a weekend warrior like me, you may value the stand enough to spend the extra money on the DeWalt.
About the setbacks, only a few users have cited that the dado blade is hardly accommodated perfectly and that it features a flat-track gauge instead of a T-track, which might not keep the miter gauge appropriately in place. Other than that, this table saw is popular and it enjoys good reviews. So, if you value efficiency and meticulous works, this is the saw you should get.
As with many table saws, the included plastic miter gauge isn’t nearly as precise as the fence and so I made angled cuts on a miter saw. If you are hoping to use this saw in lieu of a miter saw, you’ll probably want to invest in a higher-quality third party miter gauge. You can also attach a vacuum to this saw’s dust collection port for easy cleaning.

table saw parts Amazon.com


I have read dozens of reviews for Dewalt,Bosch,Baileigh,Grizzly and others and from my perspective (regarding Dewalt at least), Black&dDecker/Stanley have turned the product line , for the most part into junk. I have read reviews that indicate outright, that the table is not level, the fence is warped and if you want accurate cuts, then possibly you should look elsewhere.
The DeWalt doesn’t go above and beyond here but has some standard safety equipment as part of its Site-Pro Guarding System. The Blade Guard Assembly is a standard clear plastic set of guards that allows the wood to be fed to the blade but shields you from putting hands on the exposed blade in a slip. The guards will lock in a raised position when you need to see the blade—for example, when adjusting the blade height—which lessens the temptation to remove this safety feature when it’s in your way.

With a maximum cut depth of 3.125 inches and a 32.5-inch rip capacity, the 10-inch blade of this DeWalt table saw handled all the relatively light-duty board ripping I needed from it, but I also tested it against a variety of plywood and other board sizes to assess its capability. The 15-amp motor is fairly standard for this contractor or job site level of table saw, and none of the boards I threw at it caused it to bind—good news, as binding is at best annoying and at worst dangerous.
Chris – Great question. If you break it down a bit you can see why. The table saw uses a much smaller blade so the demand on that saw is actually quite a bit less. Also, if you make the table saw 120, you need another battery, and the conversion cable….the saw becomes VERY expensive. Just my two cents…but I’m fairly sure this is what kept it at 60v….it’s damn impressive though.

10 inch table saw Amazon.com


The DeWalt doesn’t go above and beyond here but has some standard safety equipment as part of its Site-Pro Guarding System. The Blade Guard Assembly is a standard clear plastic set of guards that allows the wood to be fed to the blade but shields you from putting hands on the exposed blade in a slip. The guards will lock in a raised position when you need to see the blade—for example, when adjusting the blade height—which lessens the temptation to remove this safety feature when it’s in your way.

dewalt dwe7491 uk Amzon.com


The latest DeWalt Table Saw is a compact 10-inch job site power saw with a number of great features. First of all, it has a rack and pinion telescoping fence which will let you make fence adjustments easily. This saw has a 24-inch rip capacity so you can use this for a variety of materials. It has an onboard storage system so you can carry tools with ease.

dewalt dwe7491 with stand Amzon.com


Now I am supposed to box it up (an enormously difficult task in itself because how tightly it is packed), somehow pick up a 110lb 4′ x 3′ x 3′ box (with weak cardboard that tears if you use the included handles) on my own to put it into my vehicle, drive to the nearest store (an hour round trip), somehow get a 110lb 4′ x 3′ x 3′ box out of the vehicle, lug it into the store, wait in line to return it, then presumably wait while another one is shipped to me (the local store has none of these in stock).
The DeWalt doesn’t go above and beyond here but has some standard safety equipment as part of its Site-Pro Guarding System. The Blade Guard Assembly is a standard clear plastic set of guards that allows the wood to be fed to the blade but shields you from putting hands on the exposed blade in a slip. The guards will lock in a raised position when you need to see the blade—for example, when adjusting the blade height—which lessens the temptation to remove this safety feature when it’s in your way.

metabo hpt table saw Amazon.com

×