Chris – Great question. If you break it down a bit you can see why. The table saw uses a much smaller blade so the demand on that saw is actually quite a bit less. Also, if you make the table saw 120, you need another battery, and the conversion cable….the saw becomes VERY expensive. Just my two cents…but I’m fairly sure this is what kept it at 60v….it’s damn impressive though.
Prior to deploying the power loss reset feature there had been many job site horror stories of unattended table saws starting up upon power restoration.  Sometimes this restart caused material damage or personal injury.   This usually happened when the saw operator did not think to turn off the tool before walking away to go restore power. In the meantime, other people have leaned on, temporarily placed tools or even building materials on the saw, a blade spinning disaster waiting to happen.
With a maximum cut depth of 3.125 inches and a 32.5-inch rip capacity, the 10-inch blade of this DeWalt table saw handled all the relatively light-duty board ripping I needed from it, but I also tested it against a variety of plywood and other board sizes to assess its capability. The 15-amp motor is fairly standard for this contractor or job site level of table saw, and none of the boards I threw at it caused it to bind—good news, as binding is at best annoying and at worst dangerous.
The Dewalt Cordless 8-1/4” Table Saw power switch is located on the front, lower left area of the saw and has a large red stop switch that can also be accessed easily with your knee. The power switch is electronic and the saw operator now has to push a green “on” button as opposed to pulling on the “red” power lever as was the case with older models.  The power switch also has a flip over safety cover that can be secured with a pad lock. The padlock hole diameter requires a ¼” maximum diameter padlock

What is a fence? How important is it in a table saw? It gives you an option for horizontal or vertical adjustments. A good rip fence should be aligned to the blade at all times. Without a fence, everything will be disgusting. Ensure that it is heavy and that it can glide smoothly across the rails. Also, make sure that the locking mechanism is perfect and convenient.
Now I am supposed to box it up (an enormously difficult task in itself because how tightly it is packed), somehow pick up a 110lb 4′ x 3′ x 3′ box (with weak cardboard that tears if you use the included handles) on my own to put it into my vehicle, drive to the nearest store (an hour round trip), somehow get a 110lb 4′ x 3′ x 3′ box out of the vehicle, lug it into the store, wait in line to return it, then presumably wait while another one is shipped to me (the local store has none of these in stock).

best table saw Amazon.com


I have read dozens of reviews for Dewalt,Bosch,Baileigh,Grizzly and others and from my perspective (regarding Dewalt at least), Black&dDecker/Stanley have turned the product line , for the most part into junk. I have read reviews that indicate outright, that the table is not level, the fence is warped and if you want accurate cuts, then possibly you should look elsewhere.

dewalt dwe7491 nz Amzon.com


Regular table saws usually have powerful motors that can give you of 3 to 5 HP at 240V. Powerful benchtop saws such as these can take larger materials like wooden flooring, logs, and lumber. On the other hand, smaller and more compact table saws have direct-drive motors that run on 120 V power at 2 HP. This kind of saw will work with thinner materials like wooden panels, vinyl, laminates and thin metal sheets.

bordssåg - dewalt dwe7491-qs Amzon.com


Upon unboxing, I wasn’t sure how much I cared that the built-in stand for this saw had wheels, but, boy, did I ever use them. If weather rolled in, the saw folded up and rolled to shelter in the garage. This was extremely convenient since I did my cutting in the driveway and stored the saw in the garage overnight. This maneuverability might be less useful to you if you plan to use the saw primarily in your garage where you could build or buy a semi-permanent stand rather than use the fold-up stand of this model. There is also on-board storage for the power cord and the loose parts such as the miter gauge and guards, making it completely self-contained.
The design is among the first ones to vary voltage in alignment to the outfitted tool. Its versatility is unmatched. The battery usage can be easily shared as you customize the operation itself. Because of its lightweight and small nature, users can easily move it from one place to another. It also doesn’t require lots of space, which is why it is perfect for home garages and commercial spaces alike.

porter cable table saw Amazon.com


The DEWALT DWE7491RS is a very good job site table saw. I’d even go so far as to say I think it’s the best overall job site + mobile stand option out there. This is a pretty bold statement considering I’ve been a huge fan of the Bosch saws for years. My assessment is based on the combination of power, quality build, cut capacity, and an effective mobile solution.

table saw Amazon.com


The design is among the first ones to vary voltage in alignment to the outfitted tool. Its versatility is unmatched. The battery usage can be easily shared as you customize the operation itself. Because of its lightweight and small nature, users can easily move it from one place to another. It also doesn’t require lots of space, which is why it is perfect for home garages and commercial spaces alike.

porter cable table saw Amazon.com


Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
DEWALT’s recent release of three new job site table saws is capped off with the all new DWE7491RS. This 10″ job site table saw with roller stand is their premium offering. We recently also reviewed the DWE7480 and DWE7490X which were released with this saw. The DWE7491RS is very similar to the DWE7490X except that it has a larger rip capacity and a much nicer stand. 

small table saw Amazon.com


The legs fold easily with an intuitive mechanism that feels well thought out, and the safety attachments stow away within the unit, reducing its form factor and allowing it to be tucked away in a corner when not in use. However, the unit does weigh 90 pounds, so if you’re going to be loading it in and out of a truck bed several times a day or needing to haul it up and down the stairs where the wheels can’t help you, you may want to look at a lighter job site saw that dispenses with the stand.

hercules table saw Amazon.com


Got mine yesterday. Set it up. Cuts very fast. My concern is when I put a straight edge against the fence vertically, it only touches the fence at the top and bottom. There’s about a 0.025″ gap in the middle. Is this a concern for accuracy? I guess I could add a thin piece of hardwood to the face of the fence to make it more flat and perpendicular. I also don’t find an adjustment for the perpendicularity of the fence face to the table. Any thoughts?
Further testing showed that the red “Stop” lever was the cause, not the power switch.  After turning on the saw, the red stop lever would drop too hard onto the stop button and turn the saw off.   After conferring with the product manager at Dewalt, it was determined that the red stop lever spring force was too high.  The units we tested was from a “manufacturing sample lot.”  MSL’s are the first time the plant does a big run of the product and Dewalt then has time to refine and make adjustments, before the tool goes to production.

laguna f2 table saw Amazon.com

×