The built-in rack and pinion fence system, which acts as a guide for boards that runs parallel to the blade, adjusts by hand and is both easy to use and very accurate. I learned to trust the fence and its measurements once I got the saw set up, and it made my workflow faster knowing I didn’t have to measure everything four times to double-check the DeWalt.
Blades come in various types and sizes. There are rip blades for cutting along the wood grains, hollow ground blades ideal for various materials, crosscut blades suitable for smooth and precise cuts, and combination blades for that double up as blades for crosscutting and ripping. Depending on what you do the most, it’s necessary to choose the right blade type and size that will get the job done with the most ease.
A table saw is only as good as its blades. There are a variety of saw blades with varying diameter, arbor size, number of teeth, kerf size, speed, application, and material. Most common table saws use 10 or 12” saw blades with an average number of teeth at24 to 80. And when it comes to the material used, carbide and carbon steel are the most common however you will also find very strong diamond blades.

industrial table saw Amazon.com


In the short period that this particular table saw has been on the market, it is clear that it is not your average power tool. The sales have been good, which is no surprise as the DCS7485T1 is a beautifully compact and cordless table saw. It makes use of balanced power and portability. At only 48 pounds in weight and a no-load speed of 5800 rpm, you can blast plywood among other timber sizes with ease.
The “Work Support / Narrow Ripping Fence” option is a nice addition and one that I have come to enjoy on Dewalt saws.  When used as a support feature it helps keep boards wider than the table top from dipping down when the fence is extended. When used as a narrow rip accessory it provides an extra 2-inches of clearance between the blade and the fence. This helps keep you hand further away from the spinning blade.
DEWALT’s recent release of three new job site table saws is capped off with the all new DWE7491RS. This 10″ job site table saw with roller stand is their premium offering. We recently also reviewed the DWE7480 and DWE7490X which were released with this saw. The DWE7491RS is very similar to the DWE7490X except that it has a larger rip capacity and a much nicer stand.

12 inch table saw Amazon.com


With a maximum cut depth of 3.125 inches and a 32.5-inch rip capacity, the 10-inch blade of this DeWalt table saw handled all the relatively light-duty board ripping I needed from it, but I also tested it against a variety of plywood and other board sizes to assess its capability. The 15-amp motor is fairly standard for this contractor or job site level of table saw, and none of the boards I threw at it caused it to bind—good news, as binding is at best annoying and at worst dangerous.

dewalt dwe7491 opinie Amzon.com


Regular table saws usually have powerful motors that can give you of 3 to 5 HP at 240V. Powerful benchtop saws such as these can take larger materials like wooden flooring, logs, and lumber. On the other hand, smaller and more compact table saws have direct-drive motors that run on 120 V power at 2 HP. This kind of saw will work with thinner materials like wooden panels, vinyl, laminates and thin metal sheets.

dewalt dwe7491 test Amzon.com


Got mine yesterday. Set it up. Cuts very fast. My concern is when I put a straight edge against the fence vertically, it only touches the fence at the top and bottom. There’s about a 0.025″ gap in the middle. Is this a concern for accuracy? I guess I could add a thin piece of hardwood to the face of the fence to make it more flat and perpendicular. I also don’t find an adjustment for the perpendicularity of the fence face to the table. Any thoughts?
Regular table saws usually have powerful motors that can give you of 3 to 5 HP at 240V. Powerful benchtop saws such as these can take larger materials like wooden flooring, logs, and lumber. On the other hand, smaller and more compact table saws have direct-drive motors that run on 120 V power at 2 HP. This kind of saw will work with thinner materials like wooden panels, vinyl, laminates and thin metal sheets.

circular saw table Amazon.com


Blades come in various types and sizes. There are rip blades for cutting along the wood grains, hollow ground blades ideal for various materials, crosscut blades suitable for smooth and precise cuts, and combination blades for that double up as blades for crosscutting and ripping. Depending on what you do the most, it’s necessary to choose the right blade type and size that will get the job done with the most ease.

dewalt dwe7491x Amzon.com


Chris – Great question. If you break it down a bit you can see why. The table saw uses a much smaller blade so the demand on that saw is actually quite a bit less. Also, if you make the table saw 120, you need another battery, and the conversion cable….the saw becomes VERY expensive. Just my two cents…but I’m fairly sure this is what kept it at 60v….it’s damn impressive though.

used table saws for sale Amazon.com


Smaller, portable table saw models have direct-drive motors that can operate on 120 V power to produce 2 HP. This is enough motor power to take on thinner materials. Table saws with more powerful motors are usually stationary saws that produce between 3 to 5 HP. Table saws with stronger motors rely on a belt drive to transfer the power from the motor to the blade and these operate on 240 V.
There are a lot of obvious reasons why the Skilsaw Portable Worm Drive Table Saw is top quality. Foremost, it is the first worm drive table, therefore, all other similar products are just based on this portable table saw. The Skilsaw is a brass-geared worm drive table saw that provides top power for maximum torque with its 5 HP dual-field motor for improved cutting speed. The selling point is its portability and compact design which makes it transportable anywhere.

dewalt dwe7491 tischkreissäge Amzon.com


I only have two minor concerns with this saw but they are so small that this saw still gets a 5 star rating.  DEWALT could step up the game on the dust collection if they offer users an effective way of using the dust port on the blade guard. Maybe they offer an accessory splitter and hose package. My other concern is the plastic parts on the fence where it connects to the table. I suspect those parts could break when they are cold if you remove the fence and toss it in the trailer or back of your truck. Again, these are minor in comparison to the rest of the saw (food for thought on the next design).

table saw extension Amazon.com


As with many table saws, the included plastic miter gauge isn’t nearly as precise as the fence and so I made angled cuts on a miter saw. If you are hoping to use this saw in lieu of a miter saw, you’ll probably want to invest in a higher-quality third party miter gauge. You can also attach a vacuum to this saw’s dust collection port for easy cleaning.
It accommodates a clean workspace with its dust port that you can link to the external accessories to keep that messy dust away. The face is great, easy to set up, and in its category, it is the best fence. You can adjust it with accuracy and quickly use the pinion fence rail and the rack. The only complaint is perhaps the miter gauge, otherwise, DeWalt DW745 is the best table saw you could ever have.

The blade is adjustable from 0-45 degrees for a variety of bevel applications. This DeWalt Table Saw has a 15-amp motor for cutting hardwood and even pressure-treated lumber. This will let you make cuts to a depth of 3- 1/8 inches at 90 degrees and 2 – ¼ inches at 45 degrees. Other important features include a coated table surface and a metal roll cage to protect the tool. This weighs 45 pounds and therefore it is easy to lift and take to your workspace or at the worksite.

dewalt dw745-xe vs dwe7491-xe Amzon.com


A table saw is only as good as its blades. There are a variety of saw blades with varying diameter, arbor size, number of teeth, kerf size, speed, application, and material. Most common table saws use 10 or 12” saw blades with an average number of teeth at24 to 80. And when it comes to the material used, carbide and carbon steel are the most common however you will also find very strong diamond blades.

laguna table saw Amazon.com

×